| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 3 May 2023 22:32:17 +0530
From: Mukesh Ojha <quic_mojha@...cinc.com>
To: <agross@...nel.org>, <andersson@...nel.org>,
<konrad.dybcio@...aro.org>, <corbet@....net>,
<keescook@...omium.org>, <tony.luck@...el.com>,
<gpiccoli@...lia.com>, <catalin.marinas@....com>,
<will@...nel.org>, <krzysztof.kozlowski+dt@...aro.org>,
<robh+dt@...nel.org>, <linus.walleij@...aro.org>,
<linux-gpio@...r.kernel.org>, <srinivas.kandagatla@...aro.org>
CC: <linux-arm-msm@...r.kernel.org>,
<linux-remoteproc@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-hardening@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-doc@...r.kernel.org>, "Mukesh Ojha" <quic_mojha@...cinc.com>
Subject: [PATCH v3 03/18] docs: qcom: Add qualcomm minidump guide
Add the qualcomm minidump guide for the users which
tries to cover the dependency and the way to test
and collect minidump on Qualcomm supported platforms.
Signed-off-by: Mukesh Ojha <quic_mojha@...cinc.com>
---
Documentation/admin-guide/qcom_minidump.rst | 246 ++++++++++++++++++++++++++++
1 file changed, 246 insertions(+)
create mode 100644 Documentation/admin-guide/qcom_minidump.rst
diff --git a/Documentation/admin-guide/qcom_minidump.rst b/Documentation/admin-guide/qcom_minidump.rst
new file mode 100644
index 0000000..062c797
--- /dev/null
+++ b/Documentation/admin-guide/qcom_minidump.rst
@@ -0,0 +1,246 @@
+Qualcomm Minidump Feature
+=========================
+
+Introduction
+------------
+
+Minidump is a best effort mechanism to collect useful and predefined
+data for first level of debugging on end user devices running on
+Qualcomm SoCs. It is built on the premise that System on Chip (SoC)
+or subsystem part of SoC crashes, due to a range of hardware and
+software bugs. Hence, the ability to collect accurate data is only
+a best-effort. The data collected could be invalid or corrupted, data
+collection itself could fail, and so on.
+
+Qualcomm devices in engineering mode provides a mechanism for generating
+full system ramdumps for post mortem debugging. But in some cases it's
+however not feasible to capture the entire content of RAM. The minidump
+mechanism provides the means for selecting region should be included in
+the ramdump.
+
+::
+
+ +-----------------------------------------------+
+ | DDR +-------------+ |
+ | | SS0-ToC| |
+ | +----------------+ +----------------+ | |
+ | |Shared memory | | SS1-ToC| | |
+ | |(SMEM) | | | | |
+ | | | +-->|--------+ | | |
+ | |G-ToC | | | SS-ToC \ | | |
+ | |+-------------+ | | | +-----------+ | | |
+ | ||-------------| | | | |-----------| | | |
+ | || SS0-ToC | | | +-|<|SS1 region1| | | |
+ | ||-------------| | | | | |-----------| | | |
+ | || SS1-ToC |-|>+ | | |SS1 region2| | | |
+ | ||-------------| | | | |-----------| | | |
+ | || SS2-ToC | | | | | ... | | | |
+ | ||-------------| | | | |-----------| | | |
+ | || ... | | |-|<|SS1 regionN| | | |
+ | ||-------------| | | | |-----------| | | |
+ | || SSn-ToC | | | | +-----------+ | | |
+ | |+-------------+ | | | | | |
+ | | | | |----------------| | |
+ | | | +>| regionN | | |
+ | | | | |----------------| | |
+ | +----------------+ | | | | |
+ | | |----------------| | |
+ | +>| region1 | | |
+ | |----------------| | |
+ | | | | |
+ | |----------------|-+ |
+ | | region5 | |
+ | |----------------| |
+ | | | |
+ | Region information +----------------+ |
+ | +---------------+ |
+ | |region name | |
+ | |---------------| |
+ | |region address | |
+ | |---------------| |
+ | |region size | |
+ | +---------------+ |
+ +-----------------------------------------------+
+ G-ToC: Global table of content
+ SS-ToC: Subsystem table of content
+ SS0-SSn: Subsystem numbered from 0 to n
+
+The core of minidump feature is part of Qualcomm's boot firmware code.
+It initializes shared memory(SMEM), which is a part of DDR and
+allocates a small section of it to minidump table i.e also called
+global table of content (G-ToC). Each subsystem (APSS, ADSP, ...) has
+their own table of segments to be included in the minidump, all
+references from a descriptor in SMEM (G-ToC). Each segment/region has
+some details like name, physical address and it's size etc. and it
+could be anywhere scattered in the DDR.
+
+Minidump kernel driver concept
+------------------------------
+
+Qualcomm minidump kernel driver adds the capability to add linux region
+to be dumped as part of ram dump collection. At the moment, shared memory
+driver creates plaform device for minidump driver and give a means to
+APSS minidump to initialize itself on probe.
+
+This driver provides ``qcom_apss_minidump_region_register`` and
+``qcom_apss_minidump_region_unregister`` API's to register and unregister
+apss minidump region. It also gives a mechanism to update physical/virtual
+address for the client whose addresses keeps on changing e.g Current stack
+address of task keep on changing on context switch for each core. So these
+clients can update their addresses with ``qcom_apss_minidump_update_region``
+API.
+
+The driver also supports registration for the clients who came before
+minidump driver was initialized. It maintains pending list of clients
+who came before minidump and once minidump is initialized it registers
+them in one go.
+
+To simplify post mortem debugging, driver creates and maintain an ELF
+header as first region that gets updated each time a new region gets
+registered.
+
+The solution supports extracting the ramdump/minidump produced either
+over USB or stored to an attached storage device.
+
+Dependency of minidump kernel driver
+------------------------------------
+
+It is to note that whole of minidump thing depends on Qualcomm boot
+firmware whether it supports minidump or not. So, if the minidump
+smem id is present in shared memory, it indicates that minidump
+is supported from boot firmware and it is possible to dump linux
+(APSS) region as part of minidump collection.
+
+How a kernel client driver can register region with minidump
+------------------------------------------------------------
+
+Client driver can use ``qcom_apss_minidump_region_register`` API's to
+register and ``qcom_apss_minidump_region_unregister`` to unregister
+their region from minidump driver.
+
+Client need to fill their region by filling qcom_apss_minidump_region
+structure object which consist of the region name, region's
+virtual and physical address and its size.
+
+Below is one sample client driver snippet which try to allocate
+a region from kernel heap of certain size and it writes a certain
+known pattern (that can help in verification after collection
+that we got the exact pattern, what we wrote) and registers it with
+minidump.
+
+ .. code-block:: c
+
+ #include <soc/qcom/qcom_minidump.h>
+ [...]
+
+
+ [... inside a function ...]
+ struct qcom_apss_minidump_region region;
+
+ [...]
+
+ client_mem_region = kzalloc(region_size, GFP_KERNEL);
+ if (!client_mem_region)
+ return -ENOMEM;
+
+ [... Just write a pattern ...]
+ memset(client_mem_region, 0xAB, region_size);
+
+ [... Fill up the region object ...]
+ strlcpy(region.name, "REGION_A", sizeof(region.name));
+ region.virt_addr = client_mem_region;
+ region.phys_addr = virt_to_phys(client_mem_region);
+ region.size = region_size;
+
+ ret = qcom_apss_minidump_region_register(®ion);
+ if (ret < 0) {
+ pr_err("failed to add region in minidump: err: %d\n", ret);
+ return ret;
+ }
+
+ [...]
+
+
+Test
+----
+
+Existing Qualcomm devices already supports entire ddr dump (also called
+full dump) by writing appropriate value to Qualcomm's top control and
+status register(tcsr) in driver/firmware/qcom_scm.c .
+
+SCM device Tree bindings required to support download mode
+For example (sm8450) ::
+
+ / {
+
+ [...]
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-sm8450", "qcom,scm";
+ [... tcsr register ... ]
+ qcom,dload-mode = <&tcsr 0x13000>;
+
+ [...]
+ };
+ };
+
+ [...]
+
+ soc: soc@0 {
+
+ [...]
+
+ tcsr: syscon@...0000 {
+ compatible = "qcom,sm8450-tcsr", "syscon";
+ reg = <0x0 0x1fc0000 0x0 0x30000>;
+ };
+
+ [...]
+ };
+ [...]
+
+ };
+
+User of minidump can pass qcom_scm.download_mode="mini" to kernel
+commandline to set the current download mode to minidump.
+Similarly, "full" is passed to set the download mode to full dump
+where entire ddr dump will be collected while setting it "full,mini"
+will collect minidump along with fulldump.
+
+Writing to sysfs node can also be used to set the mode to minidump.
+
+::
+ echo "mini" > /sys/module/qcom_scm/parameter/download_mode
+
+Once the download mode is set, any kind of crash will make the device collect
+respective dump as per set download mode.
+
+Dump collection
+---------------
+
+The solution supports extracting the minidump produced either over USB or
+stored to an attached storage device.
+
+By default, dumps are downloaded via USB to the attached x86_64 machine
+running PCAT (Qualcomm tool) software. Upon download, we will see
+a set of binary blobs starts with name md_* in PCAT configured directory
+in x86_64 machine, so for above example from the client it will be
+md_REGION_A.BIN. This binary blob depends on region content to determine
+whether it needs external parser support to get the content of the region,
+so for simple plain ASCII text we don't need any parsing and the content
+can be seen just opening the binary file.
+
+To collect the dump to attached storage type, one need to write appropriate
+value to IMEM register, in that case dumps are collected in rawdump
+partition on the target device itself.
+
+One need to read the entire rawdump partition and pull out content to
+save it onto the attached x86_64 machine over USB. Later, this rawdump
+can be pass it to another tool dexter.exe(Qualcomm tool) which converts
+this into the similar binary blobs which we have got it when download type
+was set to USB i.e a set of registered region as blobs and their name
+starts with md_*.
+
+Replacing the dexter.exe with some open source tool can be added as future
+scope of this document.
--
2.7.4
Powered by blists - more mailing lists